Response SA3 E PLUS Provozní pokyny

SA3 E PLUS6 Zone Wirefree Alarm Systemwith Voice DiallerInstallation and Operating Instructions

The Remote Control uses a CR2032 type Lithium cellwhich under normal conditions will have a typical lifein excess of 1 year. Under normal battery con

When considering and deciding upon the mountingposition for the PIR Detector the following pointsshould be considered to ensure trouble f

Note: On initial installation the PIR Detector shouldbe set into Walk Test mode ready for testing.8. The PIR Detector incorporates a sensitivity featu

Installing and setting the MagneticContact DetectorsEnsure that the system is in Test mode.1.Remove the battery cover by sliding and lifting itoff. (

8. Slide the two batteries supplied into the batteryholder, ensuring that the positive (+) side isuppermost on each battery as it is ins

The Solar Siren contains a sophisticated radioreceiver. However, reception of radio signals can beaffected by the presence of metallic objects

Setting the Solar SirenEnsure that the Solar Siren main configuration switchif fitted on the LED strobe board is set to “SIREN” foruse with this alarm

single long beep/LED flash followed immediatelyby two short beeps/LED flashes to indicate that ithas switched into Service Mode.Operating Mode:

Hard-Wired Solar Siren TestPressThe internal relay driving the hardwired siren will beswitched ON for a period of approximately 5 seconds.Zone

PressThe Arm and Part-Arm LEDs will illuminate and allZone, Fire and tamper LEDs will flash.The system is now in Programme ModeNote: After pro

Kit Contents 3Introduction and Overview 4 System

Press the key corresponding to the required delaysetting required, the corresponding zone LED willilluminate as the setting is changed.Pr

Entry/Exit Warning ToneDefault setting: ONPressThe zone 1 LED will illuminate to indicate the currentstatus of the Entry/Exit warning tone.LED ON

Note: Panic switch, 24 Hour Intruder and Fire modesall operate on a 24 hour basis, (i.e. they are able toinitiate a Full Alarm condition at a

Replay Alarm MessageThe recorded alarm message may be replayed andlistened to using the telephone handset of a phoneconnected to anothe

When leaving the premises, the system should beArmed. However, before doing so, check that allwindows are closed and locked, all

Disarming the SystemThe system can be disarmed using either the RemoteControl or the Control Panel as follows:Remote Control:Press the but

26PIR Movement Detector:Under low battery conditions the LED behind theDetector lens will flash when movement is detected toindicate that the b

Zone Settings

28TroubleshootingControl Unit not working – Power LED OFF1. Mains power failure – check if other electricalcircuits are operable.2. Check that the mai

29PIR Movement Detector not detecting aperson’s movement1. Check battery connections are good.2. Sensitivity detection set too low – reset to highsens

3Alarm Components:1 x 6 Zone LED Control Panel with Voice Dialler2 x PIR Movement Detectors2 x Magnetic Contact Detectors1 x Remote Control1

30Extending your Alarm SystemYour system may be extended to provide additional protection by adding further PIR Movement Detectors, MagneticContact De

Notes:31

Response Electronics Ltd.Roman House, Lysons Avenue, Ash Vale, Surrey GU12 5QFEmail: [email protected]: www.ResponseElectronics.com

System ArmingThe system has a ‘Full Arm’ and a ‘Part-Arm’ mode.‘Full Arm’ will arm all zones while the ‘Part-Arm’ modewill only arm the zones that are

sequence and replay the recorded alarm messages forthe set ‘Play Time’. The recipient can acknowledgethe message by pressing the

6The example below shows a typical propertyincorporating the suggested positions for the Control Panel, PIR and Magnetic Detectors fo

Control Panel7Positioning the Control PanelWhen choosing a suitable location for the ControlPanel, the following points should be considered.1.

4.Fit two 18mm No. 4 screws into the top holes untilalmost fully home and hang the Control Panel overthe screws using the two keyhole slots in the top

Connect the BT plug on the other end of the leadto an appropriate telephone outlet.If the cable supplied is not long enough to reach asuitable phone