Response SL5 Manuál s instrukcemi stáhnout pdf (Strana 35)

SYSTEM SETUP

The parameters in this menu allow the configuration of

general system parameters, such as Alarm Duration

and control of any hardwired or output relay alarm

contacts. This section also contains the basic setup

information for the systems telephone dialler interface

which must be configured appropriately if any of the

telephone based functionality is to be used.

Refer to System Setup diagram on page 34.

Scroll through the top level programming menu until

‘2. SYSTEM SETUP’ is displayed and press .

Note: After completing the system setup press

to return to the top level programming menu.

Scroll through the menu until ‘2. SYSTEM SETUP’ is

displayed on the LCD and press .

After configuring the system parameters press to

return to the top level programming menu.

LEARN REMOTE CONTROLS

AND KEYPADS

Allows up to 6 Remote Controls or Remote keypads to

be linked to the system and their ID codes learnt into

memory.

Scroll through the Zone menu until option ‘2.1 Remotes’

is displayed. The number of Remote Controls/Keypads

already linked will be shown, (e.g. if there are two

Remotes Controls and one Remote Keypad linked

the display will show ‘2.1 Remotes = 3’).

Linking a Remote Control or Remote Keypad to

the Control Panel:

Note: If there are already 6 Remote

Controls/Keypads linked to the Control Panel

then it will not be possible to link any more.

Attempting to learn a 7th device will cause the

panel to produce a single long beep and display

‘Cannot Learn - System Full’ message on

screen for 3s.

To learn a new Remote or Keypad ID code and

link it to the selected zone press .

The panel will now listen for a valid signal from

a new Remote Control or Keypad.

The Panel will remain in Learn Mode for

30s. If a valid signal is not received from a

new device within 30s it will automatically

exit Learn Mode and return to the top of

level 2.0.

Send DISARM from the new Remote Control or

Remote Keypad as follows…

Press on the Remote Control, or

Press

on the Remote Keypad.

If the device is new and not already linked to

the system the control panel will produce two

short beeps and the display will show ‘New

Device’ and the type or the detected device;

(e.g. Remote or Keypad).

ENTER

ESC

ENTER

ESC

x = No of remotes/keypads linked

2.1 Remotes = x

Edit->Enter

2.1 Remotes = x

1->Del Learn->3

1 = Delete or

3 = Learn

Confirm Delete

YES->1 3->NO

devices already

linked?

Delete confirmed

within 15s?

Send Disarm

waiting 30s...

Device Deleted

Wait...

1 = Delete

press 1 to confirm delete

press 3 to cancel

15s time-out or auto cancel

display for 3s

YES

Send Disarm

waiting 30s...

Signal

received within 30s

from Remote/Keypad not

yet linked?

YES

New Device

xxxxxx

Send Part-Arm

waiting 15s...

Remote/Keypad

code confirmed within

15s?

Device Confirmed

xxxxxx

Saving

New Device

display for 3s

YES

display for 3s

3 = Learn

Keypad User Access Code

? ? ? ?

Note: If the device is already linked

to the control panel then the panel will

produce a single long beep and the

received signal from the device will

be ignored.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 63 64

Komentáře k této Příručce

Žádné komentáře

Response SL5 Manuál s instrukcemi Strana 35

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Response SL5