Response SL5 Provozní pokyny stáhnout pdf (Strana 40)

OPERATION

38 SA5

When leaving the premises, the system must be

Armed. However, before doing so, check that all

windows are closed and locked, all protected doors

are closed and PIR Movement Detectors are not

obstructed. Ensure that pets are restricted to areas

not protected by PIR Movement Detectors.

The system has three arming modes, ARM, Part-Arm

1 and Part-Arm 2. The Part-Arm modes allow for

selected zones to be left in a Disarmed state whilst the

remainder of the system is Armed.

When the system is Armed the mode being activated

will be displayed on the screen followed by the status

of the Latch Key feature. The programmed system

exit-delay will be displayed and counted don on the

screen. If exit-delay beeps are enabled the panel will

beep with the beep rate increasing in steps as the

exit-delay expires. At the end of the Exit period all

active zones will be fully Armed. By this time the

user must have left the property and closed the final

protected door.

If while the system is armed a detector on an active

zone is triggered the programmed entry-delay for that

zone will be displayed and counted down on the

screen. If entry-delay beeps are enabled the panel will

beep with the beep rate increasing in steps as the

entry-delay expires. If the system has not been

Disarmed when the entry-delay expires a Full Alarm

will occur. (Note: if the entry-delay for the zone

triggering the alarm is disabled then an alarm will

occur immediately the detector is triggered). Details

of the zone event that triggered the alarm will be

recorded in the Event-Log.

At the end of the programmed alarm duration the Siren

and Control Panel alarms will stop and the system will

automatically re-Arm itself, (subject to the conditions

of the Zone Lockout feature.

Notes: - To conserve power and maximise battery

life the PIR detector will only detect

movement if there has been no movement

detected within the previous 2 minutes.

- If the External Solar Siren is fitted and the 3

minute limit is enabled then the external

siren will shut down when the programmed

alarm duration expires or after 3 minutes,

whichever occurs first.

Voice Dialler

If an alarm condition occurs and the Voice dialler is

activated then the first enabled phone number in the

dialling sequence will be called and the recorded

alarm message will be replayed for the programmed

“Play Time” period. The recipient should acknowledge

the message by pressing the button on their

telephone keypad to shut down the dialler. If an

acknowledgment signal is not received, then the next

enabled number in the call sequence will be called. The

dialler will continue calling each enabled number in turn

until either all numbers in the sequence have been

dialled the set number of times or the dialling sequence

is cancelled by an acknowledged signal from a recipient.

ARMING THE SYSTEM

The system can be set in FULL ARM mode using either

the Remote Control or the Control Panel as follows:

a) Press on the Remote Control, or

b) Press

, ,

on the Control Panel.

PART ARMING THE SYSTEM:

PART-ARM 1

The system can be set in PART-ARM 1 mode using either

the Remote Control or the Control Panel as follows:

a) Press on the Remote Control, or

b) Press

, ,

on the Control Panel.

PART ARMING THE SYSTEM:

PART-ARM 2

The system can be set in PART-ARM 2 mode using either

the Remote Control or the Control Panel as follows:

a) Press , on the Remote Control,

OPERATING INSTRUCTIONS

? ? ? ?

ENTER

User Access Code

? ? ? ?

ENTER

User Access Code

Note:

Unless the Dial Delay (see system setup

menu) has been disabled there will be a 30s delay

between an alarm occuring and the dialler activating.

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 51 52

Komentáře k této Příručce

Žádné komentáře

Response SL5 Provozní pokyny Strana 40

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Response SL5